Product Overview
The 200 kVA Dry Type Transformeris designed for indoor power distribution where electrical isolation and load reliability are important. Its VPI (Vacuum Pressure Impregnation) insulationreinforces the windings while retaining some mechanical flexibility, helping withstand thermal stress from load fluctuations and repeated start-ups. This construction provides an alternative to cast-resin designs for projects requiring dependable transformer performance under changing load conditions.
Automatic Winding Machine Manufacturing Coils for
200 kVA Dry Type Transformers
Technical Specifications
|
Parameter |
Standard Specification |
|
Product Name |
200 kVA Dry-Type Transformer |
|
Transformer Type |
Three-Phase Cast-Resin Dry-Type Distribution Transformer |
|
Rated Capacity |
200 kVA |
|
Number of Phases |
Three-phase |
|
Rated Frequency |
50 Hz |
|
Rated Primary Voltage |
11 kV |
|
Rated Secondary Voltage |
0.415 kV |
|
HV Tapping Range |
±2 × 2.5%, 5 positions |
|
Tap-Changing Method |
De-energized tap changing |
|
Vector Group |
Dyn11 |
|
Short-Circuit Impedance |
4.0% |
|
No-Load Current |
≤2.0% |
|
Cooling Method |
AN, air-natural |
|
Insulation Construction |
Vacuum-cast epoxy-resin insulation with fully encapsulated HV windings |
|
Winding Material |
Copper |
|
Core Material |
Cold-rolled grain-oriented silicon steel |
|
Thermal Insulation Class |
Class F |
|
Winding Temperature Rise |
100 K |
|
Partial Discharge Level |
≤10 pC |
|
Environmental / Climatic / Fire Class |
E2, C2, F1 |
|
Enclosure Protection Degree |
IP23 |
|
Temperature Monitoring |
PT100 sensors, digital temperature controller, alarm and trip contacts |
|
Installation |
Indoor installation, continuous duty |
|
Service Conditions |
Maximum ambient temperature: 40°C; maximum altitude: 1,000 m |
|
Certification Standards |
Available according to IEC, IEEE/ANSI, UL, CSA, DOE (where applicable), CE/EN, UKCA, GOST/EAC, SASO/SABER, SONCAP, ISO, and other required certification schemes |
Advantages of CHBEB 200 kVA Dry Type Transformer
CHBEB 200 kVA dry type transformers combine natural air cooling with VPI insulation to support reliable indoor operation and simplify routine maintenance.
Natural Convection Cooling
Cooling ducts between the primary and secondary windings allow heat to dissipate through natural air circulation. As warm air rises, cooler air enters from below, helping remove operating heat without mechanical fans. The oil-free design also eliminates insulating oil maintenance and the need for oil containment measures.
Moisture-Resistant VPI Insulation
The windings are impregnated with insulating varnish through the Vacuum Pressure Impregnation (VPI) process. Once cured, the coating helps protect the winding insulation against moisture exposure under suitable operating conditions. This supports insulation reliability in indoor environments where humidity and temporary shutdowns must be considered.
Simplified Routine Maintenance
The air-cooled design avoids the need for cooling pumps, fans, and insulating oil testing. Routine maintenance can focus on inspecting the windings, checking electrical connections, and keeping ventilation openings free of dust and obstructions. This simplifies maintenance planning while helping the transformer maintain reliable operating conditions.




Typical Application Context
- Medical Imaging and Healthcare Facilities
- Precision Manufacturing Workshops
- Commercial Office Buildings
- Robotic Assembly Lines
- Industrial Control Rooms
- Commercial Building Substations
- HVAC and Mechanical Plant Rooms
- Laboratories and Testing Facilities
200 kVA dry type isolation transformer powering medical
MRI equipment.
Customize 200 kVA Dry Type Transformer for Your Power Distribution Project
CHBEB provides configurable electrical, winding, cooling, protection, and documentation options to match project-specific power distribution requirements.
- Electrical Ratings - Customize primary and secondary voltage, frequency, impedance, vector group, and tap configuration according to project requirements.
- Winding & Core Materials - Select copper or aluminum windings and suitable core materials according to required electrical performance and operating conditions.
- Cooling Configuration - Configure natural air or forced-air cooling according to the required load capacity, installation conditions, and operating requirements.
- Insulation & Protection - Configure cast-resin insulation, temperature monitoring, enclosure protection, and other electrical protection requirements for the intended installation environment.
- Dimensions & Installation - Customize overall dimensions, terminal arrangements, enclosure configuration, and other structural details to suit available installation space and system connections.
- Testing & Documentation - Provide project-specific testing, technical drawings, nameplate information, and inspection documents according to customer or project requirements.

Quality Assurance & Testing by CHBEB for Transformer Manufacturing
CHBEB applies quality controls throughout material inspection, production, and final testing to maintain consistent performance and reliability for dry type transformers.
Incoming Material Inspection
Inspect silicon steel core materials, winding conductors, cast-resin insulation materials, and other key components before production. Material properties are verified against applicable GB/T and IEC requirements to ensure consistent input quality.
01
Production Process Control
Monitor core lamination, winding dimensions, insulation application, and cast-resin curing throughout manufacturing. Key process controls help maintain dimensional accuracy, insulation integrity, and consistent winding quality for dry type transformers.
02
In-Factory Quality Testing
Perform voltage ratio, winding resistance, load and no-load loss, impedance voltage, insulation resistance, withstand voltage, and partial discharge tests according to applicable IEC 60076 and GB 1094 standards. These tests verify the transformer's electrical performance and insulation condition before shipment.
03
Third-Party Testing
Support independent testing and certification through recognized organizations such as KEMA and CQC for applicable transformer projects, providing additional verification for project-specific quality and compliance requirements.
04
R&D Innovations in CHBEB Dry Type Transformer Manufacturing
CHBEB dry type transformers incorporate advanced R&D engineering to deliver maximum operational reliability and performance across demanding industrial environments.
Low-Loss Design
CHBEB optimizes magnetic circuit design and uses high-performance silicon steel sheets to improve the efficiency of dry type transformers. These technologies enable no-load losses to be reduced by 15–20% and load losses by 10–15%, helping lower energy consumption during long-term operation.
High Reliability Design
CHBEB develops reinforced winding, insulation, and structural designs to withstand demanding electrical and mechanical conditions. Its dry type transformers have passed short-circuit, overload, and vibration tests, with an annual product failure rate of less than 0.05%, supporting stable and reliable long-term operation.
High-Temperature Tolerance
CHBEB develops optimized winding and insulation systems for stable performance under elevated temperatures. Enhanced thermal design enables dry type transformers to maintain reliable operation at 95°C for 1,000 hours, supporting consistent electrical and insulation performance in high-temperature environments.
Material Innovation
CHBEB applies high-quality silicon steel sheets and advanced insulation materials to improve the electrical, thermal, and mechanical performance of dry type transformers. These material innovations can extend service life by 20–30% and increase efficiency by 5–8%, supporting more durable and energy-efficient operation.
Comprehensive Service Support from CHBEB for Your Transformer Projects
CHBEB provides practical support from technical evaluation and project coordination to delivery and after-sales service.
Technical Support & Free Design Drawings
CHBEB provides technical assistance and drawings to help customers confirm transformer specifications and equipment requirements before production.
Support includes:
• Free technical drawings for project evaluationa
• Transformer specification and selection support
• Electrical and installation requirement consultation
• Product dimension and interface confirmation
• Responsive technical communication
Fast Production & Logistics Support
CHBEB coordinates production and shipment according to project schedules, product requirements, and delivery conditions.
Support includes:
• Standard lead time of 3–6 weeks
• Expedited delivery available within 1 week
• Production scheduling based on project requirements
• Export packaging for transformer transportation
• Shipping and logistics coordination
After-Sales & Lifecycle Support
CHBEB provides technical assistance and warranty coverage to support reliable transformer operation throughout its service life.
After-sales support includes:
• 3-year warranty for complete transformers
• 2-year warranty for spare parts
• Free lifecycle maintenance guidance
• Installation and commissioning guidance
• Technical troubleshooting and operation support
FAQ
Q: Can CHBEB customize the 200 kVA dry type transformer for my project?
A: Yes. We can review your voltage ratings, installation dimensions, enclosure requirements, and applicable standards before confirming the configuration.
Q: What information should I provide to get a quotation?
A: Please share the primary and secondary voltages, frequency, quantity, installation environment, and destination country. A technical specification sheet can help us prepare an accurate quotation.
Q: Can the 200 kVA transformer be supplied with an enclosure?
A: Yes. Enclosure options can be discussed according to the installation environment, ventilation requirements, and protection level specified for your project.
Q: What documents can CHBEB provide with the transformer?
A: Available documents can include technical drawings, test reports, and product documentation. Please specify any project-specific inspection or compliance requirements before placing your order.
Q: What is the lead time for a 200 kVA dry type transformer?
A: The typical delivery lead time is approximately 15–20 days, depending on order specifications and production scheduling.
Q: What is the Customization Process?
A: CHBEB's standard customization process is: Requirement Analysis → Technical Proposal & Quotation → Detailed Engineering Design → Manufacturing & Quality Control → Packaging & Logistics → Commissioning & After-Sales Support.
Hot Tags: 200 kva dry type transformer, China 200 kva dry type transformer manufacturers, suppliers, factory, 1000 Kva Dry Type Transformer, 225 kva dry type transformer, dry type power transformer, air insulated dry type, cast coil dry type transformer, air cooled transformer dry type